Nokia Cracked Phoenix Installaion

[bb5_4wx]

I'm New to this forum, hope I'm welcome here.

Does anyone ave a problem in installing the Nokia Phoenix (Cracked) software? I want to share on how to install. If anyone is interested, please let me know. I've been using the software a year now without any dongle. It is good for flashing BB5 using DKU2 cable. and much more usefull with PBB.

[reimon23]

by the way...
welcome here bro....

can you upload the software bro...? with the flash file and steps in flashing...

TIA

[lecnoj]

Welcome to GSMPH bro... You can share it here bro...

[bb5_4wx]

by the way...
welcome here bro....

can you upload the software bro...? with the flash file and steps in flashing...

TIA

Bro, medyo malaki ang file its almost 2G kung kasama ang flash file, here you can download ;

http://homepages.nildram.co.uk/~mobile02/65405373_phoenix_service_sw_2006_12_5_136.exe

- the following software:
1 - Diego (e.g.: 55667793_Diego_3_06.msi)
2 - Phoenix 2004 + crack (e.g. : phoenix_service_sw_2004_39_7_70.EXE + 1-crack_dongle_phoenix_all_.EXE)
3 - Phoenix 2006 (e.g. : phoenix_service_sw_2006_12_5_136.rar



- the firmware of your phone. (check the file ‘last firmware’ for the latest versions of your bb5 phone at the date of appearance of this tutorial)

- the DKU-2 cable and the phone, of course.

Some of these files are archived on volumes. Unpack them all in the same folder and you will finally get the file you want. For Phoenix 2004, do “Save as” in order to download it, and change it in “.EXE”.


Step N° 1 - INSTALL DIEGO

- Run and install the following file: 55667793_Diego_3_06.msi

- If you get an error during the installation, it’s because you didn’t uninstall the Nokia connectivity cable driver!


Step N° 2 - INSTALL PHOENIX SERVICE 2004 WITH THE CRACK

- Open the crack first. Just open it, don’t run it now!

- Start installing phoenix 2004. During the installation you’ll get an error message.

- Press on “Retry” and run the crack immediately after! (Check that the destination folder is Windows/system32).

If you’re not fast enough, the message will reappear and you’ll have to re-run the crack the same way as above (but faster…)

- You’ll get 2 error messages, just press OK, and then Finish.

- You successfully installed phoenix service 2004.

Restart your PC.


Step N° 3 - INSTALL PHOENIX 2006

You have the shortcut for Phoenix on your desktop. Run it, and you might get several times the message "dskey not found!”. This is normal, just press « ok », and eventually Phoenix should open.

- Don’t close the program. You must only minimize the window.

- Run phoenix_service_sw_2006_12_5_136.EXE. You shouldn’t have any error!

- Make sure you don’t restart the PC at the end of the installation. Just choose "restart my PC later" and then Finish.

Now you can close the window of Phoenix that you have minimized.

Go to the folder Program files/Nokia/phoenix and copy this entire folder on your desktop.

Restart your PC.

If you have any error messages after the reboot, just press « Cancel ».
Go to /Program files/Nokia/, delete the folder phoenix, then replace it by the folder that you saved on your desktop. Now Re-run the crack of Phoenix 2004.

You can now run Phoenix 2006.


Step N° 4 – INSTALL THE CABLE

It is advisable to close the applications you don’t need during the flashing (like antivirus, anti-spy ware etc).

Connect your USB cable (DKU2 or another) to the PC, and connect your started phone.

Wait for Windows XP to install all the drivers (it’s better to not have unknown hardware devices), and then don’t touch your phone anymore because the cable doesn’t hang on very well and it might disconnect!

Now you have to execute these steps in phoenix:

File / Manage connection / New/ select USB / press Finish / Apply and Close.


Step N° 5 - FLASHING THE PHONE

- Put the firmware folder on your desktop. (e.g. RM36 for a Nokia 6680)
It should contain 2 files (this might vary depending on your phone model and download source):
One (MCU) with the .COR extension and the other one (PPM) with the .V30 extension.

- Do the following in phoenix: Flashing / sw update
You should see the name of the firmware folder (like RM36) on the top of the phoenix window. If you can see it, you’re on the good way.

- On the first line (Image File), browse for your file that ends by .COR .

- On the second line (PPM File), browse for your file that ends by .V30 .

Press START and don’t touch your phone anymore.

Wait for a message!
Phoenix will tell you to press the ON key of your phone and OK on the Phoenix software!

Firmware upgrade was done!